# Main - Clock-Locked Echo Room - SignalPath
Patch: [[Patches/Main/Main - Clock-Locked Echo Room]]
Build: [[Patches/Main/Main - Clock-Locked Echo Room - Build|Build]]
## Overview
The Mother-32 sequencer plays a Plaits pluck. Shades mixes the pluck with whatever comes back around the loop and feeds Disting #1, a clocked echo. That echo goes out through the Mother-32 ladder and VCA and back into Shades, so every repeat passes the filter once more. Disting #1's mix output then feeds Disting #2, a clocked ping-pong delay at a different fraction of the same clock, which spreads the repeats across the stereo field. One Mother-32 LFO clocks both delays, so turning its rate changes the size of the room without changing the ratio between the two delays. A-180-1 grouping is check panel.
```mermaid
flowchart LR
M32S[Mother-32 sequencer] -- "gate" --> P[Plaits pluck]
M32S -- "KB pitch" --> P
P --> Sh[Shades mix]
Sh --> D1[Disting #1 B-4 echo]
LFO[Mother-32 LFO SQ] --> Mult[A-180-1]
Mult --> D1
Mult --> D2[Disting #2 C-3 ping-pong]
D1 -- "B delay only" --> VCF[Mother-32 ladder + VCA]
VCF -- "loop return" --> Sh
D1 -- "A mix" --> D2
D2 -- "A" --> O[A-540 line out]
D2 -- "B" --> O
linkStyle 0 stroke:#d62828,stroke-width:3px
linkStyle 1 stroke:#9e9e9e,stroke-width:3px
linkStyle 2 stroke:#e0b800,stroke-width:3px
linkStyle 3 stroke:#e0b800,stroke-width:3px
linkStyle 4 stroke:#2a9d3a,stroke-width:3px
linkStyle 5 stroke:#2a9d3a,stroke-width:3px
linkStyle 6 stroke:#2a9d3a,stroke-width:3px
linkStyle 7 stroke:#e0b800,stroke-width:3px
linkStyle 8 stroke:#e0b800,stroke-width:3px
linkStyle 9 stroke:#e0b800,stroke-width:3px
linkStyle 10 stroke:#e0b800,stroke-width:3px
linkStyle 11 stroke:#e0b800,stroke-width:3px
```
**Cable colors:** [[Cable Colors]] after [Learning Modular](https://learningmodular.com/choosing-patch-cables/): ⚪ Gray 1 V/oct · 🔵 Blue modulation · 🟡 Yellow audio · 🔴 Red gates/triggers · 🟢 Green clock/sync · ⚫ Black external
## Why one echo turns into many
A room is a lot of echoes, so start with one. Disting #1 runs B-4 Clockable Delay/Echo with its own feedback (Z) all the way down, so its B output (delay only) is a single copy of the input, late by 5/16 of the clock period. That copy goes into the Mother-32 EXT. AUDIO, through the ladder and the VCA, and back into Shades channel 2, which sums it with the dry pluck on channel 1 and sends the lot back into Disting #1. Every lap comes out one more delay time later. One echo becomes a chain of echoes.
## Why the tail dies instead of piling up
A loop with a gain of one or more never stops: each lap is as loud as the last, and it piles up into a howl. Two things keep this one in check. Shades channel 2 (and the Mother-32 VOLUME) set the gain of each lap below one, so each repeat is quieter than the one before. That is the **decay** knob. The ladder filter cuts some top end on every pass, so the tail also gets darker as it fades, which is what a real room does to sound bouncing off soft surfaces. CUTOFF is the **tone** knob. MIX sits fully clockwise and VCA MODE on ON, so the filter only hears the loop return and the VCA never closes on it. VCF MOD AMOUNT stays at 0, because the same LFO is busy as the clock.
## Why it smears instead of ticking
A single echo line repeats at one steady spacing, which sounds like a metronome. Disting #1's A output is the mix: with Z at zero, per the manual, that is basically everything that went in (the pluck plus every lap of the loop). It feeds Disting #2, running C-3 Clockable Ping Pong Delay, at 3/16 of the clock period. Each repeat from the loop gets copied again at a spacing that does not line up with the first one (5:3), and the copies alternate left and right. The repeats stop landing on a grid and start to scatter in time and space. Disting #2's own Z adds a few more bounces without the filter, so keep it modest.
## Why one knob changes the room size
Both Distings set their delay time from the time between rising edges on Y. Both Y inputs get the same Mother-32 LFO SQ through the A-180-1. Disting #1 multiplies the period by 5/16 and Disting #2 by 3/16, so at 4 Hz they are about 78 ms and 47 ms. Speed the LFO up and both get shorter together; slow it down and both get longer. The ratio between them is locked by the multipliers, so the room keeps its shape and just changes size. Past about 30 Hz the delays get down to a few milliseconds and the loop starts ringing at a pitch, like a comb filter. Below about 2 Hz it is slapback, not a room.
## Short version
Plaits is the clap in the room, Disting #1 and the ladder are the walls, Disting #2 is the clutter that scatters the echoes, Shades is how hard the walls are, and the Mother-32 LFO is how far apart they are.