# Main - Clock-Locked Echo Room - Build Patch: [[Patches/Main/Main - Clock-Locked Echo Room]] Signal path: [[Patches/Main/Main - Clock-Locked Echo Room - SignalPath|SignalPath]] An incremental build of that patch. One or two cables at a time, so you can hear each stage and watch the interesting voltages on the Mordax DATA. Starting points, jack names, and the final cable list come from the patch note. DATA jack names and modes come from the official [DATA User Guide](https://mordax.link/DATA_User_Guide) (SYS V. 01.02.05, updated 230310), linked from [mordax.net](https://www.mordax.net/products/data). **Cable colors:** [[Cable Colors]] after [Learning Modular](https://learningmodular.com/choosing-patch-cables/): ⚪ Gray 1 V/oct · 🔵 Blue modulation · 🟡 Yellow audio · 🔴 Red gates/triggers · 🟢 Green clock/sync · ⚫ Black external ## Before you start - Power the case as usual. Seat the DATA in the main rack if it is not already there. The guide says its microSD card must stay in the slot during use. - Monitors or the A-540 down at first. This patch is a feedback loop, so keep a hand near Shades channel 2. A-180-1 grouping is check panel. - Set every module to the starting points in the [[Patches/Main/Main - Clock-Locked Echo Room|patch note]] before you add cables: Mother-32 sparse sequence at a slow TEMPO, MIX fully clockwise, VCA MODE ON, VOLUME 11 o'clock, VCF MODE LOW PASS, CUTOFF 12 o'clock, RESONANCE fully counter-clockwise, VCF MOD AMOUNT and VCO MOD AMOUNT at 0; Plaits second bank, fourth model (inharmonic string), HARMONICS 10 o'clock, TIMBRE 1 o'clock, MORPH 10 o'clock, attenuverters at 12 o'clock; Shades both channels in attenuator mode, channel 1 at 2 o'clock, channel 2 fully counter-clockwise; Disting #1 on **B-4**, parameter 0 at −5, parameter 1 at 0, Z fully counter-clockwise; Disting #2 on **C-3**, parameter 0 at 0, parameter 1 at −7, parameter 2 at its default, Z at 10 o'clock. - On the DATA, open the **Oscilloscope** program from the main menu. In each channel's pop-up menu, set **COUPL** to **DC**. The guide says you typically want to view signals as DC; AC coupling blocks a steady voltage and will make a clock or a stepped CV sit at 0 V or droop. Use trigger mode **AUTO** whenever the time scale is in the hundreds of milliseconds or in seconds. **DATA jacks, as named in the User Guide:** four **Input Jacks** (±10 V), four **Buffered Through Jacks**, and four **Output Jacks**. This build uses only the inputs and the throughs. The guide: "Regardless of the program running, a signal present at an Input Jack is buffered and sent back out of its corresponding Through Jack for use elsewhere in your patch." The official panel photo on mordax.net numbers those channels **1–4**; each Through Jack sits directly under its Input Jack, with a downward triangle between them. The panel does not silk-screen the words Input or Through; if your panel reads differently, check the panel. The Output Jacks (the right-hand bank, also numbered 1–4) are unused here. **Pass-through habit:** to watch a signal, unplug the destination end, go from the source into a DATA Input Jack, and continue from that channel's Buffered Through Jack to the destination. The cable color stays the color of the signal. The DATA has four channels, so they get reassigned as the build moves. A running plan is at the top of each step. ## 1. Hear the dry pluck **DATA:** channel 1 watches the Shades mix (the signal that will feed Disting #1). Channels 2–4 are free. **Cables** 1. 🔴 Red · Mother-32 GATE (out) -> Plaits TRIG (in, 3) 2. ⚪ Gray · Mother-32 KB (out) -> Plaits V/OCT (in, 5) 3. 🟡 Yellow · Plaits OUT (out, 6) -> Shades channel 1 Signal input 4. 🟡 Yellow · Shades channel 2 Signal output -> DATA channel 1 Input Jack. Leave Shades channel 1's output empty. 5. 🟡 Yellow · DATA channel 1 Buffered Through Jack -> A-540 channel A input (temporary) **Set.** Press RUN/STOP to start the Mother-32 sequence. A-540 up just enough to hear. Nothing from the Mother-32's own voice should be audible on this cable; the VCA output is not patched yet. **Listen for.** A short, slightly metallic pluck on the left, following the Mother-32 sequence, with silence between notes. **Watch on DATA.** Channel 1, Oscilloscope, TIME around 200MS, AUTO, SCALE 5.0V: a short burst on each note that dies away well before the next one. **If it doesn't sound right.** No sound: the sequencer may be stopped, or Shades channel 1 is down. One pitch only: KB may not be reaching V/OCT. A long drone: MORPH is too high, or Plaits is on the wrong model. ## 2. Start the room-size clock **DATA:** channel 1 stays on the Shades mix. Channel 2 watches the LFO clock. **Cables** 1. 🟢 Green · Mother-32 **LFO SQ** (out, ±5 V) -> DATA channel 2 Input Jack 2. 🟢 Green · DATA channel 2 Buffered Through Jack -> A-180-1 (any jack in one group; check panel for grouping) 3. 🟢 Green · A-180-1 -> Disting #1 Y (in, clock) 4. 🟢 Green · A-180-1 -> Disting #2 Y (in, clock) **Set.** Turn LFO RATE until one full square cycle takes about 250 ms (4 Hz). **Listen for.** No change yet. If the pluck now wobbles in pitch or brightness, a MOD AMOUNT knob is not at 0. **Watch on DATA.** Channel 2, Oscilloscope, TIME around 500MS, AUTO, SCALE 5.0V: a ±5 V square. Count two cycles across about 500 ms. That period is the room size. **If it doesn't sound right.** No square: check the A-180-1 grouping on the panel. Pluck wobbling: VCF MOD AMOUNT or VCO MOD AMOUNT is up. ## 3. A single echo **DATA:** channel 1 Shades mix, channel 2 clock, channel 3 watches Disting #1 B (delay only). **Cables.** Unplug DATA channel 1's Through Jack from the A-540. Then: 1. 🟡 Yellow · DATA channel 1 Buffered Through Jack -> Disting #1 X (in, audio) 2. 🟡 Yellow · Disting #1 A (out, mix) -> A-540 channel A input (temporary) 3. 🟡 Yellow · Disting #1 B (out, delay only) -> DATA channel 3 Input Jack 4. 🟡 Yellow · DATA channel 3 Buffered Through Jack -> A-540 channel B input (temporary) **Set.** Disting #1 Z stays fully counter-clockwise. **Listen for.** The dry pluck on the left, and one copy of it on the right about 78 ms later. One echo, no more. **Watch on DATA.** Channels 1 and 3 together, Oscilloscope, TIME around 200MS, AUTO, SCALE 5.0V: the burst on channel 3 sits a fixed distance after the burst on channel 1. Turn LFO RATE a little and watch that gap stretch or shrink. **If it doesn't sound right.** Several echoes on the right: Z is not all the way down. No echo: the clock is not reaching Y, or parameter 1 is not 0. ## 4. Close the loop through the ladder **DATA:** channel 1 Shades mix, channel 2 clock, channel 3 Disting #1 B, now heading for the Mother-32. **Cables.** Unplug DATA channel 3's Through Jack from the A-540. Then: 1. 🟡 Yellow · DATA channel 3 Buffered Through Jack -> Mother-32 EXT. AUDIO (in) 2. 🟡 Yellow · Mother-32 VCA (out) -> Shades channel 2 Signal input **Set.** Shades channel 2 starts fully counter-clockwise. Bring it up slowly toward 12 o'clock. Then try CUTOFF from 10 o'clock to 2 o'clock. **Listen for.** On the left, the single echo now repeats: a chain of echoes that get quieter and darker on every lap. Shades channel 2 sets how long the chain lasts. CUTOFF sets how fast it goes dull. **Watch on DATA.** Channel 1, Oscilloscope, TIME around 500MS, AUTO, SCALE 5.0V: the first burst followed by a row of smaller bursts, evenly spaced, each a little lower than the last. **Quick check:** if the bursts stop shrinking and the trace fills up, the loop gain has reached one. Turn Shades channel 2 down at once. **If it doesn't sound right.** No repeats: MIX is not fully clockwise, VCA MODE is not ON, or VOLUME is down. A rising howl: Shades channel 2 or VOLUME is too high. Repeats stay bright: CUTOFF is too high. ## 5. Scatter the echoes in stereo **DATA:** channel 1 Shades mix, channel 2 clock, channel 3 loop return, channel 4 watches Disting #2 B (right output). **Cables.** Unplug Disting #1 A from the A-540. Then: 1. 🟡 Yellow · Disting #1 A (out, mix) -> Disting #2 X (in, audio) 2. 🟡 Yellow · Disting #2 A (out, left) -> A-540 channel A input 3. 🟡 Yellow · Disting #2 B (out, right) -> DATA channel 4 Input Jack 4. 🟡 Yellow · DATA channel 4 Buffered Through Jack -> A-540 channel B input **Set.** Disting #2 Z at 10 o'clock. Then sweep LFO RATE slowly over its lower half. **Listen for.** The evenly spaced chain from step 4 now gets a second set of echoes at a different spacing, bouncing left and right. The tail smears instead of ticking. Turning LFO RATE grows or shrinks the whole room; the two delays stay in the same 5:3 ratio. Faster settings squeeze it into a pitched ring; slower settings open it into slapback. **Watch on DATA.** Channels 1 and 4 together, Oscilloscope, TIME around 500MS, AUTO, SCALE 5.0V: channel 4 shows more, closer bursts than channel 1, and they do not line up with the loop's even spacing. Unsure from the manual whether the delay time glides or jumps when the clock changes, so expect some zipper or pitch-bend on the tail while you turn the knob. **If it doesn't sound right.** Nothing on the right: B is not reaching the A-540. Dry pluck leaning left: parameter 2 (input pan) sets where the input lands in the ping-pong, and its default is −32 per the manual; nudge it toward 0 if you want the dry more central, at the cost of less bounce. A harsh bright buzz on top: Disting #2 Z is too high (its repeats skip the ladder). Clicks on clock changes: turn LFO RATE more slowly. ## Full patch These are the cables from the patch note. If the DATA is still in the path, each watched signal is two cables (source to Input Jack, Buffered Through Jack to destination) instead of one. 1. 🔴 Red · Mother-32 GATE (out) -> Plaits TRIG (in, 3) 2. ⚪ Gray · Mother-32 KB (out) -> Plaits V/OCT (in, 5) 3. 🟡 Yellow · Plaits OUT (out, 6) -> Shades channel 1 Signal input 4. 🟡 Yellow · Shades channel 2 Signal output -> Disting #1 X (in, audio). Leave channel 1's output empty, so this carries the pluck plus the loop return. 5. 🟢 Green · Mother-32 **LFO SQ** (out, ±5 V) -> A-180-1 (any jack in one group; check panel for grouping) 6. 🟢 Green · A-180-1 -> Disting #1 Y (in, clock) 7. 🟢 Green · A-180-1 -> Disting #2 Y (in, clock) 8. 🟡 Yellow · Disting #1 B (out, delay only) -> Mother-32 EXT. AUDIO (in) 9. 🟡 Yellow · Mother-32 VCA (out) -> Shades channel 2 Signal input 10. 🟡 Yellow · Disting #1 A (out, mix) -> Disting #2 X (in, audio) 11. 🟡 Yellow · Disting #2 A (out, left) -> A-540 channel A input 12. 🟡 Yellow · Disting #2 B (out, right) -> A-540 channel B input With the DATA left in as of step 5, the watched paths are: cable 4 through DATA channel 1, cable 5 through channel 2, cable 8 through channel 3, and cable 12 through channel 4. Cables 1, 2, 3, 6, 7, 9, 10, and 11 run direct. The DATA can stay in or come out. To remove it, patch each watched signal straight from source to destination, as in the list above. The sound should not change; you just lose the graphs. **What it should sound like, once the last cable is in:** a short metallic pluck followed by a quick cluster of echoes that bounce left and right and get darker and quieter until they are gone. CUTOFF sets how dark the tail goes, Shades channel 2 sets how long it hangs, and LFO RATE shrinks or grows the whole room while the two delays keep their 5:3 spacing.