# Main - Clock-Locked Echo Room
Case: **Eurorack 001 Installed** (main rack). Each module is used once.
Sources: [Moritz Klein, The reverb video is finally here!](https://www.patreon.com/moritzklein/posts/reverb-video-is-175889690) (Patreon, Reverb Series, 2026-11-20) · early-access video [Designing a reverb circuit without springs, plates, or code](https://www.youtube.com/watch?v=Nat7S3OKDV0)
Moritz builds his reverb from a handful of analog chips. This patch borrows the ideas named in his chapter list (a single echo, a chain of echoes, scattering in time, stopping the pile-up, tone, decay, room size, locking the ratio) and builds them from two Distings and the Mother-32 ladder. It is a nod to his work, not a copy, and it will sound like a small grainy echo room, not a plate.
Jack labels from the disting mk4 User Manual v4.18 (B-4, C-3), the Mother-32 Users Manual, the Plaits and Shades (2020) manuals, and ladik.eu (A-540). A-180-1 grouping: check panel.
Signal path explained: [[Patches/Main/Main - Clock-Locked Echo Room - SignalPath|SignalPath]]
Incremental build: [[Patches/Main/Main - Clock-Locked Echo Room - Build|Build]]
## Modules
- Moog Mother-32: sequencer (pitch and gate for Plaits), LFO as the room-size clock, and the ladder filter + VCA as the damping inside the echo loop
- Mutable Instruments Plaits: the dry pluck (inharmonic string)
- Mutable Instruments Shades: mixes the dry pluck with the filtered loop return; channel 2 is the decay knob
- Doepfer A-180-1: splits the clock to both Distings
- Expert Sleepers Disting mk4 (#1): **B-4 Clockable Delay/Echo**, the echo inside the loop
- Expert Sleepers Disting mk4 Special Edition (#2): **C-3 Clockable Ping Pong Delay (Z feedback)**, the scattering stage
- Ladik A-540: stereo out
**Cable colors:** [[Cable Colors]] after [Learning Modular](https://learningmodular.com/choosing-patch-cables/): ⚪ Gray 1 V/oct · 🔵 Blue modulation · 🟡 Yellow audio · 🔴 Red gates/triggers · 🟢 Green clock/sync · ⚫ Black external
## Cables
1. 🔴 Red · Mother-32 GATE (out) -> Plaits TRIG (in, 3)
2. ⚪ Gray · Mother-32 KB (out) -> Plaits V/OCT (in, 5)
3. 🟡 Yellow · Plaits OUT (out, 6) -> Shades channel 1 Signal input
4. 🟡 Yellow · Shades channel 2 Signal output -> Disting #1 X (in, audio). Leave channel 1's output empty, so this carries the pluck plus the loop return.
5. 🟢 Green · Mother-32 **LFO SQ** (out, ±5 V) -> A-180-1 (any jack in one group; check panel for grouping)
6. 🟢 Green · A-180-1 -> Disting #1 Y (in, clock)
7. 🟢 Green · A-180-1 -> Disting #2 Y (in, clock)
8. 🟡 Yellow · Disting #1 B (out, delay only) -> Mother-32 EXT. AUDIO (in)
9. 🟡 Yellow · Mother-32 VCA (out) -> Shades channel 2 Signal input
10. 🟡 Yellow · Disting #1 A (out, mix) -> Disting #2 X (in, audio)
11. 🟡 Yellow · Disting #2 A (out, left) -> A-540 channel A input
12. 🟡 Yellow · Disting #2 B (out, right) -> A-540 channel B input
## Starting points
- **Mother-32:**
- Sequence: a sparse pattern, a few notes with rests between them so you can hear the tail. TEMPO slow.
- MIX fully clockwise, so only EXT. AUDIO (the loop return) reaches the filter. The VCO is out of the sound.
- VCA MODE **ON**, so the loop is not chopped by the EG. VOLUME 11 o'clock to start.
- VCF MODE LOW PASS. CUTOFF 12 o'clock (this is the **tone** knob), RESONANCE fully counter-clockwise.
- VCF MOD AMOUNT and VCO MOD AMOUNT at 0. The LFO is running as the clock, and you do not want it sweeping the filter.
- LFO RATE for about 4 Hz (a 250 ms period; read it on the DATA in the Build). This is the **room size** knob.
- **Plaits:** second bank, fourth model (inharmonic string). HARMONICS 10 o'clock, TIMBRE 1 o'clock, MORPH (decay) 10 o'clock for a short pluck. TIMBRE, FM and MORPH attenuverters at 12 o'clock. Leave LEVEL unpatched.
- **Shades:** both channels in attenuator mode. Channel 1 (dry level) at 2 o'clock. Channel 2 (the **decay** knob) fully counter-clockwise to start, then bring it up slowly.
- **Disting #1 (B-4):** parameter 0 (delay time multiplier) **−5** (5/16 of the clock period, about 78 ms at 4 Hz). Parameter 1 (output mode) **0**: A is mix, B is delay only. Z (internal feedback) fully counter-clockwise; the loop through the Mother-32 does the repeating.
- **Disting #2 (C-3):** parameter 0 (output mode) **0** (A/B are dry plus delay). Parameter 1 (delay time multiplier) **−7** (3/16, about 47 ms at 4 Hz). Parameter 2 (input pan) at its default. Z (feedback) 10 o'clock.
## Level notes
- EXT. AUDIO is a unity-gain input built for 10 V peak-to-peak, and the VCA output is ±5 V typical, so the loop sits near unity with VOLUME and Shades channel 2 both up. That is the point where the echoes pile up. Keep one of them below 1 o'clock until you know where the edge is.
- Both Distings run B-4 and C-3 at about 19 kHz (a quarter of the standard sample rate, per the manual), so the repeats lose top end on their own. The Mother-32 ladder takes off more on every lap.
- B-4 tops out at about 1700 ms and C-3 at about 900 ms. A slower clock is halved until it fits, so a very slow LFO will not give you a very big room.
## What it should sound like
A short metallic pluck followed by a quick cluster of echoes that bounce left and right and get darker and quieter until they are gone. CUTOFF sets how dark the tail goes, Shades channel 2 sets how long it hangs, and LFO RATE shrinks or grows the whole room while the spacing between the two delays stays in the same 5:3 ratio. Push LFO RATE up and the echoes squeeze into a pitched, comb-filter ring; pull it down and it opens into slapback.