# Crossover - Turntable Through the Mother-32 Ladder - Build Patch: [[Patches/Crossover/Crossover - Turntable Through the Mother-32 Ladder]] Signal path: [[Patches/Crossover/Crossover - Turntable Through the Mother-32 Ladder - SignalPath|SignalPath]] An incremental build of that patch. One or two cables at a time, so you can hear each stage and watch the interesting voltages on the Mordax DATA. Starting points, jack names, and the final cable list come from the patch note. DATA jack names and modes come from the official [DATA User Guide](https://mordax.link/DATA_User_Guide) (SYS V. 01.02.05, updated 230310), linked from [mordax.net](https://www.mordax.net/products/data). **Cable colors:** [[Cable Colors]] after [Learning Modular](https://learningmodular.com/choosing-patch-cables/): ⚪ Gray 1 V/oct · 🔵 Blue modulation · 🟡 Yellow audio · 🔴 Red gates/triggers · 🟢 Green clock/sync · ⚫ Black external ## Before you start - Power the cases as usual. The DATA lives in **Eurorack 001 Installed** (BLACK panel, 16 HP), per [[Rack]] and [[Modules/DATA]]. Use it as usual on any signal that already passes through the main rack. For Moog or SeaHorse signals, fly a pass-through over, or skip the DATA on those cables. If flying cables isn't practical, treat those "Watch on DATA" steps as optional. The guide says its microSD card must stay in the slot during use. - The A-541 down at first. Phono Preamp MONO and Echo jack silk-screens are check panel. The cases run on separate supplies; if you get hum when you join them, look at grounding before blaming the patch. - Set every module to the starting points in the [[Patches/Crossover/Crossover - Turntable Through the Mother-32 Ladder|patch note]] before you add cables: Phono Preamp on PHONO (LINE only for a line source), volume up until the record sits level with the Mother-32 VCO at MIX 12 o'clock, then MIX fully clockwise; Mother-32 VCF MODE LP, CUTOFF 12 o'clock, RESONANCE 2 o'clock, VCF MOD AMOUNT 0, VCA MODE EG, ATTACK fully counter-clockwise, DECAY 11 o'clock, SUSTAIN OFF, VOLUME 2 o'clock; Labyrinth RUN, about 5 bits on in SEQ1, SEQ2 CV RANGE 11 o'clock, CORRUPT on SEQ2 at 11 o'clock, its own VOLUME down; Echo Rate 12 o'clock, Feedback 1 o'clock, Mix 12 o'clock. Hook the turntable's ground wire to the Phono Preamp's GND connection. - On the DATA, open the **Oscilloscope** program from the main menu. In each channel's pop-up menu, set **COUPL** to **DC**. The guide says you typically want to view signals as DC; AC coupling blocks a steady voltage and will make a clock or a stepped CV sit at 0 V or droop. Use trigger mode **AUTO** whenever the time scale is in the hundreds of milliseconds or in seconds. **DATA jacks, as named in the User Guide:** four **Input Jacks** (±10 V), four **Buffered Through Jacks**, and four **Output Jacks**. This build uses only the inputs and the throughs. The guide: "Regardless of the program running, a signal present at an Input Jack is buffered and sent back out of its corresponding Through Jack for use elsewhere in your patch." The official panel photo on mordax.net numbers those channels **1–4**; each Through Jack sits directly under its Input Jack, with a downward triangle between them. The panel does not silk-screen the words Input or Through; if your panel reads differently, check the panel. The Output Jacks (the right-hand bank, also numbered 1–4) are unused here. **Pass-through habit:** to watch a signal, unplug the destination end, go from the source into a DATA Input Jack, and continue from that channel's Buffered Through Jack to the destination. The cable color stays the color of the signal. The DATA has four channels, so they get reassigned as the build moves. A running plan is at the top of each step. ## 1. Hear the record dry, then through the ladder **DATA:** channel 1 the Phono Preamp MONO output (check panel). The DATA lives in the main rack; the preamp is in the SeaHorse, so fly this cable or skip the pass-through. The Mother-32 is on the Moog 4-tier. **Cables** 1. ⚫ Black · Turntable RCA -> Phono Preamp RCA inputs 2. 🟡 Yellow · Phono Preamp MONO output (check panel) -> DATA channel 1 Input Jack 3. 🟡 Yellow · DATA channel 1 Buffered Through Jack -> A-541 channel A input (1/8″), just for a source check Then unplug that Through Jack from the A-541 and send the record into the filter: 4. 🟡 Yellow · DATA channel 1 Buffered Through Jack -> Mother-32 EXT. AUDIO (in) **Set.** First, hear the record dry so you know the source. Then go fully clockwise on MIX (EXT only). For this first ladder listen, flip VCA MODE to ON so you hear a continuous filtered wash, and set resonance at 2 o'clock. EXT. AUDIO is a unity-gain input built for 10 V peak-to-peak; the preamp's modular-level output is what you want, so do not skip it and plug a line source straight in. **Listen for.** First the dry record, then the same record through a resonant Moog ladder, still ungated. **Watch on DATA.** Channel 1, Oscilloscope, TIME around 1MS, SCALE 5.0V, trigger AUTO (the guide recommends AUTO for a mix of many signals). A busy audio waveform. **If it doesn't sound right.** Thin or quiet into the Mother-32: the preamp may be on LINE, or you skipped it. The Mother-32 VCO in the mix: MIX is not fully at EXT. ## 2. Chop it on a Labyrinth rhythm **DATA:** channel 2 SEQ1 TRIG, channel 3 SEQ2 CV. These are Moog-side signals; fly them or skip the DATA. **Cables.** Flip VCA MODE back to EG. 1. 🔴 Red · Labyrinth SEQ1 TRIG (out, 0 to 5 V) -> DATA channel 2 Input Jack 2. 🔴 Red · DATA channel 2 Buffered Through Jack -> Mother-32 GATE (in) 3. 🔵 Blue · Labyrinth SEQ2 CV (out) -> DATA channel 3 Input Jack 4. 🔵 Blue · DATA channel 3 Buffered Through Jack -> Mother-32 VCF CUTOFF (in) **Set.** About 5 bits on in SEQ1 for the chop rhythm. SEQ2 CV RANGE 11 o'clock, CORRUPT on SEQ2 at 11 o'clock. VCF MOD AMOUNT at 0. Resonance at 2 o'clock so the filter rings on each cutoff jump. Labyrinth's own VOLUME down. **Listen for.** The record sliced into resonant, gated Moog-filter stabs on a mutating Labyrinth rhythm, still without the echo or the ungated right side. **Watch on DATA.** Channel 2, Oscilloscope, TIME around 200MS to 1.0S, AUTO, SCALE 2.0V: short 0 to 5 V triggers. Channel 3, Oscilloscope or Voltage Monitor, same window, COUPL DC: a jumping cutoff CV. If the CV sits at 0 V, COUPL may be on AC. **If it doesn't sound right.** A continuous wash, no chops: VCA MODE may still be ON, or SEQ1 TRIG may not be reaching GATE. No filter jumps: SEQ2 may not be reaching CUTOFF. ## 3. Echo the chops, and put the ungated filter on the right **DATA:** channel 4 can watch the Mother-32 VCA going into the Echo. Echo jacks are check panel. **Cables** 1. 🟡 Yellow · Mother-32 VCA (out, gated) -> DATA channel 4 Input Jack 2. 🟡 Yellow · DATA channel 4 Buffered Through Jack -> Echo audio input (check panel) 3. 🟡 Yellow · Echo output (check panel) -> A-541 channel A input (1/8″) 4. 🟡 Yellow · Mother-32 VCF (out, filtered but not gated) -> A-541 channel B input (1/8″) **Set.** Echo Rate 12 o'clock, Feedback 1 o'clock, Mix 12 o'clock. VOLUME 2 o'clock sets the VCA patch-out level. **Listen for.** An echo trail on the left (the gated stabs) and, on the right, the same record through the same filter, ungated, as a continuous wash. **Watch on DATA.** Channel 4, Oscilloscope, TIME around 1MS to 10MS or a slower AUTO window: gated bursts going into the Echo. Channel 1 is still the raw record going into EXT. AUDIO. **If it doesn't sound right.** Both sides gated, or both continuous: the VCA and VCF outputs may be swapped. No echo: the Echo input and output are check panel. Hum when the cases are joined: look at grounding before blaming the patch. ## Full patch These are the cables from the patch note. If the DATA is still in the path, each watched signal is two cables (source to Input Jack, Buffered Through Jack to destination) instead of one. 1. ⚫ Black · Turntable RCA -> Phono Preamp RCA inputs 2. 🟡 Yellow · Phono Preamp MONO output (check panel) -> Mother-32 EXT. AUDIO (in) 3. 🔴 Red · Labyrinth SEQ1 TRIG (out, 0 to 5 V) -> Mother-32 GATE (in) 4. 🔵 Blue · Labyrinth SEQ2 CV (out) -> Mother-32 VCF CUTOFF (in) 5. 🟡 Yellow · Mother-32 VCA (out, gated) -> Echo audio input (check panel) 6. 🟡 Yellow · Echo output (check panel) -> A-541 channel A input (1/8″) 7. 🟡 Yellow · Mother-32 VCF (out, filtered but not gated) -> A-541 channel B input (1/8″) With the DATA left in as of step 3, the watched paths are: cable 2 through DATA channel 1, cable 3 through channel 2, cable 4 through channel 3, and cable 5 through channel 4. Cables 1, 6, and 7 run direct. The DATA can stay in or come out. To remove it, patch each watched signal straight from source to destination, as in the list above. The sound should not change; you just lose the graphs. **What it should sound like, once the last cable is in:** the record sliced into resonant, gated Moog-filter stabs on a mutating Labyrinth rhythm, with an echo trail on the left. The right side is the same record through the same filter, ungated, as a continuous wash.