# Crossover - Three-Rig Berlin Machine - Build
Patch: [[Patches/Crossover/Crossover - Three-Rig Berlin Machine]]
Signal path: [[Patches/Crossover/Crossover - Three-Rig Berlin Machine - SignalPath|SignalPath]]
An incremental build of that patch. One or two cables at a time, so you can hear each stage and watch the interesting voltages on the Mordax DATA. Starting points, jack names, and the final cable list come from the patch note. DATA jack names and modes come from the official [DATA User Guide](https://mordax.link/DATA_User_Guide) (SYS V. 01.02.05, updated 230310), linked from [mordax.net](https://www.mordax.net/products/data).
**Cable colors:** [[Cable Colors]] after [Learning Modular](https://learningmodular.com/choosing-patch-cables/): ⚪ Gray 1 V/oct · 🔵 Blue modulation · 🟡 Yellow audio · 🔴 Red gates/triggers · 🟢 Green clock/sync · ⚫ Black external
## Before you start
- Power the cases as usual. The DATA lives in **Eurorack 001 Installed** (BLACK panel, 16 HP), per [[Rack]] and [[Modules/DATA]]. Use it as usual on any signal that already passes through the main rack. For Moog or SeaHorse signals, fly a pass-through over, or skip the DATA on those cables. If flying cables isn't practical, treat those "Watch on DATA" steps as optional. The guide says its microSD card must stay in the slot during use.
- The A-540 and the Mother-32 and DFAM rear 1/4″ outputs down at first, then into the same mixer. A-180-1 grouping, Micro Sequence and SEEDS silk-screens are check panel. SEEDS has no published user manual. The cases run on separate supplies; if you get hum when you join them, look at grounding before blaming the patch.
- Set every module to the starting points in the [[Patches/Crossover/Crossover - Three-Rig Berlin Machine|patch note]] before you add cables: Mother-32 a 16-step ostinato in one minor key, no swing, saw wave, CUTOFF 1 o'clock, a little resonance, short decay, SUSTAIN OFF, TEMPO about 120 BPM; DFAM 8 steps, a pulsing kick and noise tick, PITCH knobs close; Micro Sequence clock divider ÷2, Scale on Minor, Direction Pendulum, length 8; SEEDS a bright, short sound, tuned an octave or two above the Mother-32; Beads SIZE fully clockwise (∞) so it is a delay, DENSITY counter-clockwise of noon, FEEDBACK 1 o'clock, DRY/WET 11 o'clock, REVERB 1 o'clock. Press DFAM RUN/STOP before starting the Mother-32.
- On the DATA, open the **Oscilloscope** program from the main menu. In each channel's pop-up menu, set **COUPL** to **DC**. The guide says you typically want to view signals as DC; AC coupling blocks a steady voltage and will make a clock or a stepped CV sit at 0 V or droop. Use trigger mode **AUTO** whenever the time scale is in the hundreds of milliseconds or in seconds.
**DATA jacks, as named in the User Guide:** four **Input Jacks** (±10 V), four **Buffered Through Jacks**, and four **Output Jacks**. This build uses only the inputs and the throughs. The guide: "Regardless of the program running, a signal present at an Input Jack is buffered and sent back out of its corresponding Through Jack for use elsewhere in your patch." The official panel photo on mordax.net numbers those channels **1–4**; each Through Jack sits directly under its Input Jack, with a downward triangle between them. The panel does not silk-screen the words Input or Through; if your panel reads differently, check the panel. The Output Jacks (the right-hand bank, also numbered 1–4) are unused here.
**Pass-through habit:** to watch a signal, unplug the destination end, go from the source into a DATA Input Jack, and continue from that channel's Buffered Through Jack to the destination. The cable color stays the color of the signal.
The DATA has four channels, so they get reassigned as the build moves. A running plan is at the top of each step.
## 1. Hear the ostinato and the drums, then lock them
**DATA:** channel 1 can watch Mother-32 ASSIGN, which already lives in (or can live in) the main rack. Listen to the two Moog voices at their rear outputs.
**Cables**
1. ⚫ Black · Mother-32 and DFAM from their own rear 1/4″ outputs into the same mixer.
2. 🟢 Green · Mother-32 ASSIGN (out, sequencer clock, 0 to +5 V) -> DATA channel 1 Input Jack
3. 🟢 Green · DATA channel 1 Buffered Through Jack -> A-180-1 (one group; check panel)
4. 🟢 Green · A-180-1 -> DFAM ADV / CLOCK (in)
**Set.** Press DFAM RUN/STOP first, then start the Mother-32 at about 120 BPM. The A-180-1 grouping is check panel; all three clock copies in this patch must come from one group.
**Listen for.** The Mother-32 hammers a 16-step ostinato; DFAM ticks and thumps in sync. No arpeggio and no delay yet.
**Watch on DATA.** Channel 1, Oscilloscope, TIME around 200MS to 500MS, AUTO, SCALE 2.0V: regular 0 to +5 V clock pulses. 120 BPM is 2 Hz; the Voltage Monitor may start to alias, so the Oscilloscope is the safer view.
**If it doesn't sound right.** DFAM ignoring the Mother-32: ASSIGN may not be the clock, DFAM may not have been started first, or the A-180-1 group may be wrong (check panel).
## 2. Hear SEEDS, then sequence it at half time
**DATA:** channel 2 SEEDS audio, channel 3 Micro Sequence pitch. Both of those jacks are check panel. Channel 4 can watch the clock copy going to the Micro Sequence.
**Cables**
1. 🟢 Green · A-180-1 -> Micro Sequence clock input (check panel)
2. ⚪ Gray · Micro Sequence quantized pitch output (check panel) -> DATA channel 3 Input Jack
3. ⚪ Gray · DATA channel 3 Buffered Through Jack -> SEEDS pitch CV input (check panel)
4. 🟡 Yellow · SEEDS audio output (check panel) -> DATA channel 2 Input Jack
5. 🟡 Yellow · DATA channel 2 Buffered Through Jack -> A-540 channel A input
For a first listen, you can hear SEEDS on a fixed pitch before the Micro Sequence pitch is in, then add that cable. I have no maker figure for the Micro Sequence clock-in threshold; if it misses beats, check the panel and manual.
**Set.** Divider ÷2, Scale on Minor, Direction Pendulum, length 8. Tune SEEDS an octave or two above the Mother-32. Pick the sound with its own controls; there is no published user manual for the panel.
**Listen for.** A little 8-bit arpeggio at half time, still dry, over the locked ostinato and drums.
**Watch on DATA.** Channel 3, Oscilloscope or Voltage Monitor, TIME around 500MS to 1.0S, AUTO, SCALE 2.0V: an 8-step staircase that moves at half the Mother-32 clock. Channel 2, TIME around 1MS, SCALE 5.0V: a bright, short 8-bit tone on each step. The Tuner can try this channel (27.50 Hz to 2,960 Hz).
**If it doesn't sound right.** SEEDS on one pitch: the pitch jack is check panel, or the Micro Sequence is not getting a clock (also check panel). Arpeggio at full speed: the divider may not be at ÷2.
## 3. Send SEEDS through a tempo-locked Beads delay
**DATA:** keep channel 2 on SEEDS, but reroute its Through Jack into Beads. Channel 4 watches the clock copy going to Beads SEED if it is not already on the Micro Sequence clock.
**Cables.** Unplug channel 2's Through Jack from the A-540. Then:
1. 🟢 Green · A-180-1 -> Beads SEED (in, 4)
2. 🟡 Yellow · DATA channel 2 Buffered Through Jack -> Beads IN L
3. 🟡 Yellow · Beads L (out) -> A-540 channel A input
4. 🟡 Yellow · Beads R (out) -> A-540 channel B input
**Set.** SIZE fully clockwise (∞) turns Beads into a delay. With the clock on SEED, the delay time follows the tempo. DENSITY counter-clockwise of noon for binary subdivisions. FEEDBACK 1 o'clock, DRY/WET 11 o'clock, REVERB 1 o'clock.
**Listen for.** The little SEEDS arpeggio bouncing through a tempo-locked delay across the stereo field, with the Mother-32 ostinato and DFAM still in the mixer from their rear outputs.
**Watch on DATA.** Channel 2 is still dry SEEDS going into Beads. Channel 1 is still the master clock. If you sit channel 4 on the SEED copy, those pulses should match channel 1.
**If it doesn't sound right.** Delay not in tempo: SEED may not be getting a clock, or SIZE may not be at ∞. A smear instead of a delay: DENSITY may be past noon. Hum when the cases are joined: look at grounding before blaming the patch.
## Full patch
These are the cables from the patch note. If the DATA is still in the path, each watched signal is two cables (source to Input Jack, Buffered Through Jack to destination) instead of one.
1. 🟢 Green · Mother-32 ASSIGN (out, sequencer clock, 0 to +5 V) -> A-180-1 (one group; check panel)
2. 🟢 Green · A-180-1 -> DFAM ADV / CLOCK (in)
3. 🟢 Green · A-180-1 -> Micro Sequence clock input (check panel)
4. 🟢 Green · A-180-1 -> Beads SEED (in, 4)
5. ⚪ Gray · Micro Sequence quantized pitch output (check panel) -> SEEDS pitch CV input (check panel)
6. 🟡 Yellow · SEEDS audio output (check panel) -> Beads IN L
7. 🟡 Yellow · Beads L (out) -> A-540 channel A input
8. 🟡 Yellow · Beads R (out) -> A-540 channel B input
9. ⚫ Black · Mother-32 and DFAM from their own rear 1/4″ outputs into the same mixer.
With the DATA left in as of step 3, the watched paths are: cable 1 through DATA channel 1, cable 6 through channel 2, and cable 5 through channel 3, with channel 4 free for a clock copy (cable 3 or 4). Cables 2, 7, 8, and 9 run direct.
The DATA can stay in or come out. To remove it, patch each watched signal straight from source to destination, as in the list above. The sound should not change; you just lose the graphs.
**What it should sound like, once the last cable is in:** a Berlin-school machine. The Mother-32 hammers a 16-step ostinato, DFAM ticks and thumps in sync, and a little 8-bit SEEDS arpeggio at half time bounces through a tempo-locked Beads delay across the stereo field.