# Crossover - Three-Rig Berlin Machine
Cases: **Eurorack 001 Installed** + **Synthrotek SeaHorse** + **Moog 4-tier**. Each physical module is used once. The Mother-32 and the Micro Sequence are single units, whichever case they're in today.
Source: original; extends [[Patches/Original/Berlin School Sequence and Space]]
Jack labels from the Mother-32 Users Manual, the DFAM User Guide, the Beads manual, and ladik.eu (A-540). Micro Sequence jacks from the maker page; SEEDS has no published user manual. A-180-1 grouping, Micro Sequence, and SEEDS silk-screen: check panel.
Signal path explained: [[Patches/Crossover/Crossover - Three-Rig Berlin Machine - SignalPath|SignalPath]]
Incremental build: [[Patches/Crossover/Crossover - Three-Rig Berlin Machine - Build|Build]]
## Modules
- Moog Mother-32 (Moog 4-tier / main): ostinato bass and master clock
- Moog DFAM (Moog 4-tier): analog pulse percussion
- Doepfer A-180-1 (main): clock split
- Pittsburgh Modular Micro Sequence (main / SeaHorse): arpeggio pitches at half time
- Ginko Synthese SEEDS (SeaHorse): 8-bit arpeggio voice
- Mutable Instruments Beads (main): tempo-synced delay
- Ladik A-540 (main): stereo out for the SEEDS / Beads side
**Cable colors:** [[Cable Colors]] after [Learning Modular](https://learningmodular.com/choosing-patch-cables/): ⚪ Gray 1 V/oct · 🔵 Blue modulation · 🟡 Yellow audio · 🔴 Red gates/triggers · 🟢 Green clock/sync · ⚫ Black external
## Cables
1. 🟢 Green · Mother-32 ASSIGN (out, sequencer clock, 0 to +5 V) -> A-180-1 (one group; check panel)
2. 🟢 Green · A-180-1 -> DFAM ADV / CLOCK (in)
3. 🟢 Green · A-180-1 -> Micro Sequence clock input (check panel)
4. 🟢 Green · A-180-1 -> Beads SEED (in, 4)
5. ⚪ Gray · Micro Sequence quantized pitch output (check panel) -> SEEDS pitch CV input (check panel)
6. 🟡 Yellow · SEEDS audio output (check panel) -> Beads IN L
7. 🟡 Yellow · Beads L (out) -> A-540 channel A input
8. 🟡 Yellow · Beads R (out) -> A-540 channel B input
9. ⚫ Black · Mother-32 and DFAM from their own rear 1/4″ outputs into the same mixer.
## Starting points
- **Mother-32:** a 16-step ostinato in one minor key, no swing. Saw wave, CUTOFF 1 o'clock, a little RESONANCE, short DECAY, SUSTAIN OFF. TEMPO about 120 BPM.
- **DFAM:** 8 steps, a pulsing kick and noise tick pattern. Keep the PITCH knobs close so it stays percussive. Press RUN/STOP before starting the Mother-32.
- **Micro Sequence:** clock divider ÷2 so the arpeggio runs at half time, Scale on Minor, Direction Pendulum, length 8.
- **SEEDS:** pick a bright, short sound with its own controls. Tune it an octave or two above the Mother-32.
- **Beads:**
- SIZE fully CW (∞) turns it into a delay. With the clock on SEED, the delay time follows the tempo.
- DENSITY CCW of 12 for binary subdivisions only; the further from 12, the shorter the subdivision.
- FEEDBACK 1 o'clock, DRY/WET 11 o'clock, REVERB 1 o'clock.
## Level notes
- Mother-32 ASSIGN is a 0 to 5 V clock, and DFAM ADV / CLOCK takes 0 to 5 V. The Micro Sequence clock-in threshold isn't on the maker page; if it misses beats, check the panel and manual.
- The cases run on separate supplies. If you get hum when you join them, look at grounding before blaming the patch.
## What it should sound like
A Berlin-school machine. The Mother-32 hammers a 16-step ostinato, DFAM ticks and thumps in sync, and a little 8-bit SEEDS arpeggio at half time bounces through a tempo-locked Beads delay across the stereo field.