# Crossover - Subharmonicon Plays the Seahorse - Build Patch: [[Patches/Crossover/Crossover - Subharmonicon Plays the Seahorse]] Signal path: [[Patches/Crossover/Crossover - Subharmonicon Plays the Seahorse - SignalPath|SignalPath]] An incremental build of that patch. One or two cables at a time, so you can hear each stage and watch the interesting voltages on the Mordax DATA. Starting points, jack names, and the final cable list come from the patch note. DATA jack names and modes come from the official [DATA User Guide](https://mordax.link/DATA_User_Guide) (SYS V. 01.02.05, updated 230310), linked from [mordax.net](https://www.mordax.net/products/data). **Cable colors:** [[Cable Colors]] after [Learning Modular](https://learningmodular.com/choosing-patch-cables/): ⚪ Gray 1 V/oct · 🔵 Blue modulation · 🟡 Yellow audio · 🔴 Red gates/triggers · 🟢 Green clock/sync · ⚫ Black external ## Before you start - Power the cases as usual. The DATA lives in **Eurorack 001 Installed** (BLACK panel, 16 HP), per [[Rack]] and [[Modules/DATA]]. Use it as usual on any signal that already passes through the main rack. For Moog or SeaHorse signals, fly a pass-through over, or skip the DATA on those cables. If flying cables isn't practical, treat those "Watch on DATA" steps as optional. The guide says its microSD card must stay in the slot during use. - The A-541 and the Subharmonicon rear 1/4″ output down at first. The cases run on separate supplies; if you get hum when you join them, look at grounding before blaming the patch. - Set every module to the starting points in the [[Patches/Crossover/Crossover - Subharmonicon Plays the Seahorse|patch note]] before you add cables: Subharmonicon QUANTIZE 8-ET, SEQ OCT ±1, RHYTHM 1=2, 2=3, 3=4, 4=6, 1 and 3 on SEQ 1, 2 and 4 on SEQ 2, TEMPO 11 o'clock, mixer levels around 10 o'clock; Plaits on the inharmonic string model (second bank, fourth), HARMONICS 10 o'clock, TIMBRE 12 o'clock, MORPH 1 o'clock, attenuverters at noon; Rings string resonator, polyphony 2, FREQUENCY an octave above Plaits, STRUCTURE, BRIGHTNESS and DAMPING at noon; Shades attenuator mode, channel 1 at 1 o'clock, channel 2 at 12 o'clock; Disting on **L-2**, Z positive about a third, Size 20, Feedback 24 (the default). The SEQ jacks carry only the step offsets, so set each voice's root with the FREQUENCY knobs. - On the DATA, open the **Oscilloscope** program from the main menu. In each channel's pop-up menu, set **COUPL** to **DC**. The guide says you typically want to view signals as DC; AC coupling blocks a steady voltage and will make a clock or a stepped CV sit at 0 V or droop. Use trigger mode **AUTO** whenever the time scale is in the hundreds of milliseconds or in seconds. **DATA jacks, as named in the User Guide:** four **Input Jacks** (±10 V), four **Buffered Through Jacks**, and four **Output Jacks**. This build uses only the inputs and the throughs. The guide: "Regardless of the program running, a signal present at an Input Jack is buffered and sent back out of its corresponding Through Jack for use elsewhere in your patch." The official panel photo on mordax.net numbers those channels **1–4**; each Through Jack sits directly under its Input Jack, with a downward triangle between them. The panel does not silk-screen the words Input or Through; if your panel reads differently, check the panel. The Output Jacks (the right-hand bank, also numbered 1–4) are unused here. **Pass-through habit:** to watch a signal, unplug the destination end, go from the source into a DATA Input Jack, and continue from that channel's Buffered Through Jack to the destination. The cable color stays the color of the signal. The DATA has four channels, so they get reassigned as the build moves. A running plan is at the top of each step. ## 1. Hear Plaits and Rings dry, then the drone **DATA:** channel 1 Plaits, channel 2 Rings. The DATA lives in the main rack; fly these SeaHorse signals over, or skip the pass-throughs. The Subharmonicon drone is listened at its rear output. **Cables** 1. 🟡 Yellow · Plaits OUT (out, 6) -> DATA channel 1 Input Jack 2. 🟡 Yellow · DATA channel 1 Buffered Through Jack -> A-541 channel A input (1/8″) 3. 🟡 Yellow · Rings ODD (out) -> DATA channel 2 Input Jack 4. 🟡 Yellow · DATA channel 2 Buffered Through Jack -> A-541 channel B input (1/8″) 5. ⚫ Black · The Subharmonicon's own sound comes from its rear 1/4″ output. For this first listen, strike Plaits and Rings by hand (a temporary 🔴 red trigger into Plaits TRIG and Rings STRUM, or turn FREQUENCY on Rings). Press PLAY on the Subharmonicon with mixer levels low. **Set.** A-541 up just enough. Subharmonicon mixer levels around 10 o'clock so it is a bed, not a lead. **Listen for.** Two plucked-string tones, still unsequenced, and a low Subharmonicon drone underneath from the rear output. **Watch on DATA.** Channels 1 and 2, Oscilloscope, TIME around 1MS, SCALE 5.0V: decaying string strikes. The Tuner can check either pitch (27.50 Hz to 2,960 Hz). **If it doesn't sound right.** No drone: PLAY may be off, or you are not listening at the rear output. No string strike: nothing has hit TRIG or STRUM yet, which is normal until the next step. ## 2. Let the Subharmonicon play both voices **DATA:** channel 3 SEQ 1 (pitch to Plaits), channel 4 SEQ 2 or a trigger. Pull the temporary triggers. **Cables** 1. ⚪ Gray · Subharmonicon SEQ 1 (out, −5 to +5 V) -> DATA channel 3 Input Jack 2. ⚪ Gray · DATA channel 3 Buffered Through Jack -> Plaits V/OCT (in, 5) 3. 🔴 Red · Subharmonicon TRIGGER (out, 0 to 5 V, 1 ms) -> Plaits TRIG (in, 3) 4. ⚪ Gray · Subharmonicon SEQ 2 (out) -> Rings V/OCT (in, 3) 5. 🔴 Red · Subharmonicon SEQ 2 CLK (out, 0 to 5 V) -> Rings STRUM (in, 2) To watch a trigger as well, move channel 4 onto TRIGGER or SEQ 2 CLK (0 to 5 V pulses). SEQ outs are ±5 V; Plaits TRIG and Rings STRUM read the 0 to 5 V pulses fine. **Set.** Roots from the FREQUENCY knobs, because the SEQ jacks carry only the step offsets. Plaits on a 2-and-4 grid, Rings on 3-and-6, an octave above. **Listen for.** Two plucked-string lines in a diatonic scale, in Subharmonicon polyrhythm: Plaits on SEQ 1's 2-and-4, Rings on SEQ 2's 3-and-6, drone still low underneath. **Watch on DATA.** Channel 3, Oscilloscope or Voltage Monitor, TIME around 500MS to 1.0S, AUTO, SCALE 2.0V or 5.0V: a stepped ±5 V pitch. A trigger on channel 4 should be a short 0 to 5 V pulse, not a long gate, and should not fall on every clock. **If it doesn't sound right.** Both voices on the same grid: the rhythm assignments may be swapped. Always the same root: you may have expected the SEQ jack to carry the root; set it with FREQUENCY instead. ## 3. Mix and add a stereo room **DATA:** keep the pitch and trigger watches. Unplug Plaits and Rings from the A-541 and send the mix through the Disting. **Cables.** Unplug channel 1 and 2 Through Jacks from the A-541. Then: 1. 🟡 Yellow · DATA channel 1 Buffered Through Jack -> Shades channel 1 Signal input 2. 🟡 Yellow · DATA channel 2 Buffered Through Jack -> Shades channel 2 Signal input 3. 🟡 Yellow · Shades channel 2 Signal output (channels 1 + 2; leave channel 1's output empty) -> Disting X (in) 4. 🟡 Yellow · Disting A (out) -> A-541 channel A input (1/8″) 5. 🟡 Yellow · Disting B (out) -> A-541 channel B input (1/8″) **Set.** Shades already at 1 o'clock and 12 o'clock. Disting L-2 already at a medium size, Z positive about a third. **Listen for.** The two string lines in one mix, in a stereo room, with the Subharmonicon drone still coming from its own rear output. **Watch on DATA.** Channels 1 and 2 are still the dry voices going into Shades. **If it doesn't sound right.** Only one string: Shades channel 1's output may be patched, which would break the 2-into-1 mix. Hum when the cases are joined: look at grounding before blaming the patch. ## Full patch These are the cables from the patch note. If the DATA is still in the path, each watched signal is two cables (source to Input Jack, Buffered Through Jack to destination) instead of one. 1. ⚪ Gray · Subharmonicon SEQ 1 (out, −5 to +5 V) -> Plaits V/OCT (in, 5) 2. 🔴 Red · Subharmonicon TRIGGER (out, 0 to 5 V, 1 ms) -> Plaits TRIG (in, 3) 3. ⚪ Gray · Subharmonicon SEQ 2 (out) -> Rings V/OCT (in, 3) 4. 🔴 Red · Subharmonicon SEQ 2 CLK (out, 0 to 5 V) -> Rings STRUM (in, 2) 5. 🟡 Yellow · Plaits OUT (out, 6) -> Shades channel 1 Signal input 6. 🟡 Yellow · Rings ODD (out) -> Shades channel 2 Signal input 7. 🟡 Yellow · Shades channel 2 Signal output (channels 1 + 2; leave channel 1's output empty) -> Disting X (in) 8. 🟡 Yellow · Disting A (out) -> A-541 channel A input (1/8″) 9. 🟡 Yellow · Disting B (out) -> A-541 channel B input (1/8″) 10. ⚫ Black · The Subharmonicon's own sound comes from its rear 1/4″ output. With the DATA left in as of step 3, the watched paths are: cable 5 through DATA channel 1, cable 6 through channel 2, and cable 1 through channel 3, with channel 4 free for a trigger or SEQ 2. Cables 2, 3, 4, 7, 8, 9, and 10 run direct unless you sit the DATA on one of those as well. The DATA can stay in or come out. To remove it, patch each watched signal straight from source to destination, as in the list above. The sound should not change; you just lose the graphs. **What it should sound like, once the last cable is in:** two plucked-string lines in a diatonic scale, played in Subharmonicon polyrhythm: Plaits on SEQ 1's 2-and-4 grid, Rings on SEQ 2's 3-and-6. The Subharmonicon drone sits low underneath, all in a stereo room.