# Crossover - Labyrinth and DFAM in Beads Clouds - Build Patch: [[Patches/Crossover/Crossover - Labyrinth and DFAM in Beads Clouds]] Signal path: [[Patches/Crossover/Crossover - Labyrinth and DFAM in Beads Clouds - SignalPath|SignalPath]] An incremental build of that patch. One or two cables at a time, so you can hear each stage and watch the interesting voltages on the Mordax DATA. Starting points, jack names, and the final cable list come from the patch note. DATA jack names and modes come from the official [DATA User Guide](https://mordax.link/DATA_User_Guide) (SYS V. 01.02.05, updated 230310), linked from [mordax.net](https://www.mordax.net/products/data). **Cable colors:** [[Cable Colors]] after [Learning Modular](https://learningmodular.com/choosing-patch-cables/): ⚪ Gray 1 V/oct Ā· šŸ”µ Blue modulation Ā· 🟔 Yellow audio Ā· šŸ”“ Red gates/triggers Ā· 🟢 Green clock/sync Ā· ⚫ Black external ## Before you start - Power the cases as usual. The DATA lives in **Eurorack 001 Installed** (BLACK panel, 16 HP), per [[Rack]] and [[Modules/DATA]]. Use it as usual on any signal that already passes through the main rack. For Moog or SeaHorse signals, fly a pass-through over, or skip the DATA on those cables. If flying cables isn't practical, treat those "Watch on DATA" steps as optional. The guide says its microSD card must stay in the slot during use. - The A-540 down at first. The Mother-32 sits out of this patch. The DATA already lives in the main rack, next to Beads, Stages and Shades; fly the Moog-side signals over, or skip the DATA on those cables. The cases run on separate supplies; if you get hum when you join them, look at grounding before blaming the patch. - Set every module to the starting points in the [[Patches/Crossover/Crossover - Labyrinth and DFAM in Beads Clouds|patch note]] before you add cables: Labyrinth TEMPO slow, SEQ1 and SEQ2 at different lengths (for example 7 and 6), SEQ1 AMT to QTZ, SEQ1 CV RANGE 10 o'clock, CORRUPT on both at 11 o'clock, BLEND knob at 10 o'clock, EG2 DECAY 2 o'clock; DFAM VCA EG SLOW, VCA DECAY 1 o'clock, VCO 1 and 2 FREQUENCY mid, NOISE / EXT LEVEL down, CUTOFF 12 o'clock; Beads in latched grain generation, DENSITY 2 o'clock (probability once SEED is clocked), SIZE 1 o'clock, TIME 11 o'clock with its attenurandomizer at 1 o'clock, DRY/WET 1 o'clock, REVERB 2 o'clock, FEEDBACK 10 o'clock; Stages segments 1 and 2 on RAMP, each looped, sliders high, GATE inputs empty; Shades channel 1 in attenuator mode, about 11 o'clock. - On the DATA, open the **Oscilloscope** program from the main menu. In each channel's pop-up menu, set **COUPL** to **DC**. The guide says you typically want to view signals as DC; AC coupling blocks a steady voltage and will make a clock or a stepped CV sit at 0 V or droop. Use trigger mode **AUTO** whenever the time scale is in the hundreds of milliseconds or in seconds. **DATA jacks, as named in the User Guide:** four **Input Jacks** (±10 V), four **Buffered Through Jacks**, and four **Output Jacks**. This build uses only the inputs and the throughs. The guide: "Regardless of the program running, a signal present at an Input Jack is buffered and sent back out of its corresponding Through Jack for use elsewhere in your patch." The official panel photo on mordax.net numbers those channels **1–4**; each Through Jack sits directly under its Input Jack, with a downward triangle between them. The panel does not silk-screen the words Input or Through; if your panel reads differently, check the panel. The Output Jacks (the right-hand bank, also numbered 1–4) are unused here. **Pass-through habit:** to watch a signal, unplug the destination end, go from the source into a DATA Input Jack, and continue from that channel's Buffered Through Jack to the destination. The cable color stays the color of the signal. The DATA has four channels, so they get reassigned as the build moves. A running plan is at the top of each step. ## 1. Hear Labyrinth and DFAM dry **DATA:** channel 1 Labyrinth VCA, channel 2 DFAM VCA, if you fly them over. For a first listen you can also use the two rear 1/4″ outputs, then move those signals into Beads. **Cables.** Start with a dry preview into the A-540, then we will reroute into Beads: 1. 🟔 Yellow Ā· Labyrinth VCA (out, 10 V p-p) -> DATA channel 1 Input Jack 2. 🟔 Yellow Ā· DATA channel 1 Buffered Through Jack -> A-540 channel A input 3. 🟔 Yellow Ā· DFAM VCA (out, āˆ’5 to +5 V) -> DATA channel 2 Input Jack 4. 🟔 Yellow Ā· DATA channel 2 Buffered Through Jack -> A-540 channel B input **Set.** Labyrinth RUN, slow tempo, long EG2 decay. DFAM on soft toms and wood, VCA EG slow. Press DFAM RUN/STOP; it is still on its own tempo until the next step. **Listen for.** Slowly mutating Labyrinth tones on the left, soft DFAM toms on the right, still dry and not yet locked or granulated. **Watch on DATA.** Channels 1 and 2, Oscilloscope, TIME around 1MS to see the tones, or 500MS to 1.0S (AUTO) to see the slow envelopes. SCALE 5.0V. **If it doesn't sound right.** No Labyrinth motion: CORRUPT may be down and the lengths may be the same. DFAM too snappy: VCA EG may still be FAST. ## 2. Lock the clocks, then pour them into Beads **DATA:** keep channels 1 and 2, but reroute the Through Jacks from the A-540 into Beads. Channel 3 watches Labyrinth CLOCK, channel 4 DFAM TRIGGER into Beads SEED. **Cables.** Unplug both Through Jacks from the A-540. Then: 1. 🟢 Green Ā· Labyrinth CLOCK (out, 0 to 5 V) -> DATA channel 3 Input Jack 2. 🟢 Green Ā· DATA channel 3 Buffered Through Jack -> DFAM ADV / CLOCK (in) 3. 🟔 Yellow Ā· DATA channel 1 Buffered Through Jack -> Beads IN L 4. 🟔 Yellow Ā· DATA channel 2 Buffered Through Jack -> Beads IN R 5. 🟢 Green Ā· DFAM TRIGGER (out) -> DATA channel 4 Input Jack 6. 🟢 Green Ā· DATA channel 4 Buffered Through Jack -> Beads SEED (in, 4) (judgment call) 7. 🟔 Yellow Ā· Beads L (out) -> A-540 channel A input 8. 🟔 Yellow Ā· Beads R (out) -> A-540 channel B input **Set.** Start DFAM first if you are clocking it externally. Beads DENSITY at 2 o'clock; with SEED clocked, DENSITY is probability. That SEED cable is green because it is used as a clock for grain timing (a judgment call in the patch note). **Listen for.** The two voices, now locked, scattered into rhythmic grain clouds that land on the drum steps by chance, already with a lot of room. **Watch on DATA.** Channel 3, Oscilloscope, TIME around 500MS to 1.0S, AUTO, SCALE 2.0V: a slow 0 to 5 V clock. Channel 4, same window: DFAM triggers, used here as a grain clock. Channels 1 and 2 are the dry voices going into Beads. **If it doesn't sound right.** Grains ignore the drums: SEED may not be getting the trigger, or DENSITY may be fully down (never) or fully up (always). DFAM still on its own tempo: CLOCK may not be reaching ADV / CLOCK. ## 3. Add the two Stages LFOs **DATA:** the four channels are full. The new graphs worth seeing are Stages LFO 1 (Beads TIME) and the Shades-braked LFO 2 into Labyrinth BLEND. Free channels 1 and 2 from the dry audio (patch Labyrinth and DFAM straight to Beads) and use them for the two CVs, or skip the DATA on these if you want to keep watching the audio. **Cables.** If you free channels 1 and 2: 1. 🟔 Yellow Ā· Labyrinth VCA (out, 10 V p-p) -> Beads IN L (direct; remove the DATA cables from that path) 2. 🟔 Yellow Ā· DFAM VCA (out, āˆ’5 to +5 V) -> Beads IN R (direct) 3. šŸ”µ Blue Ā· Stages output 1 (segment 1, looping RAMP) -> DATA channel 1 Input Jack 4. šŸ”µ Blue Ā· DATA channel 1 Buffered Through Jack -> Beads TIME CV input (6) 5. šŸ”µ Blue Ā· Stages output 2 (segment 2, looping RAMP) -> Shades channel 1 Signal input 6. šŸ”µ Blue Ā· Shades channel 1 Signal output -> DATA channel 2 Input Jack 7. šŸ”µ Blue Ā· DATA channel 2 Buffered Through Jack -> Labyrinth BLEND (in, āˆ’5 to +5 V) **Set.** Both Stages segments already looped, sliders high. TIME attenurandomizer at 1 o'clock. BLEND knob at 10 o'clock; the CV pushes it toward VCF. Stages outputs run 0 to 8 V and Labyrinth BLEND takes āˆ’5 to +5 V, so Shades (about 11 o'clock) is the brake. **Listen for.** The Labyrinth tone swings between folded and filtered over a long cycle, and the grain position drifts on another. Good for an hour-long ambient bed. **Watch on DATA.** Channels 1 and 2, Oscilloscope or Voltage Monitor, TIME around 1.0S to 5.0S, AUTO, COUPL DC, SCALE 2.0V. Two slow, independent ramps. Channel 2 (after Shades) should be a smaller swing than a raw 0 to 8 V Stages output. Channels 3 and 4 still show clock and SEED. **If it doesn't sound right.** No swing: the Stages segments may not be looped, or a GATE cable may have been plugged in. BLEND slams to one end: lower Shades. Hum when the cases are joined: look at grounding before blaming the patch. ## Full patch These are the cables from the patch note. If the DATA is still in the path, each watched signal is two cables (source to Input Jack, Buffered Through Jack to destination) instead of one. 1. 🟢 Green Ā· Labyrinth CLOCK (out, 0 to 5 V) -> DFAM ADV / CLOCK (in) 2. 🟔 Yellow Ā· Labyrinth VCA (out, 10 V p-p) -> Beads IN L 3. 🟔 Yellow Ā· DFAM VCA (out, āˆ’5 to +5 V) -> Beads IN R 4. 🟢 Green Ā· DFAM TRIGGER (out) -> Beads SEED (in, 4) (judgment call) 5. šŸ”µ Blue Ā· Stages output 1 (segment 1, looping RAMP) -> Beads TIME CV input (6) 6. šŸ”µ Blue Ā· Stages output 2 (segment 2, looping RAMP) -> Shades channel 1 Signal input 7. šŸ”µ Blue Ā· Shades channel 1 Signal output -> Labyrinth BLEND (in, āˆ’5 to +5 V) 8. 🟔 Yellow Ā· Beads L (out) -> A-540 channel A input 9. 🟔 Yellow Ā· Beads R (out) -> A-540 channel B input With the DATA left in as of step 3, a useful final watch is: cable 5 through DATA channel 1, cable 7 through channel 2, cable 1 through channel 3, and cable 4 through channel 4, with cables 2, 3, 6, 8, and 9 running direct. Earlier in the build, channels 1 and 2 can sit on the two dry voices instead. The DATA can stay in or come out. To remove it, patch each watched signal straight from source to destination, as in the list above. The sound should not change; you just lose the graphs. **What it should sound like, once the last cable is in:** slowly mutating Labyrinth tones and soft DFAM toms, scattered into rhythmic grain clouds that land on the drum steps by chance. The Labyrinth tone swings between folded and filtered over a long cycle. Good for an hour-long ambient bed.